One Piece Clutch Brake Removal

Ask Your Own Heavy Equipment Question. The Kiene Clutch Brake Cutter eliminates the danger and the job can be done in 15 -.

Unique Truck Equipment Kiene Clutch Brake Cutter

The tool is designed to be safe and cost-effective method of clutch brake removal.

One piece clutch brake removal. What is the easiest way to remove a one piece clutch brake 2000 Freightliner Century w 10 speed. Open the clutch brake as wide as possible. If it has a hinge on the other side you should be able to remove at this point.

The Kiene Clutch Brake Cutter eliminates the danger and the job can be done in 15 - 20 minutes No need to pull the transmission - No more torching drill through and finish with an air chisel - SAFE QUICK. Push and hold clutch down. The Kiene Diesel K-1360 one-piece clutch brake remover is a tool designed for removing a one-piece clutch brake.

The OEM brake is a 1 piece deal. Install them in the 4 cover holes and turn them finger-tight. Insure the transmission is in gear the clutch is correctly adjusted 12 gap between the release bearing housing and clutch brake and make sure the clutch linkage allows the release bearing to contact the clutch brake.

Clutch Brake Installation Instructions web only posting 7-14 INITIALLY. To replace the clutch brake you will need to remove the access cover on the bottom of the transmission bellhousing. The K-1360 Clutch Brake Cutter makes the job safer and much easier.

Drill through and then finish. Position drill guide on clutch brake. Ive heard of guys using a torch but there is a LOT of grease up in there it looks like the previous owner greased the throwout bearing every day.

Finish cut with the air chisel. The safe and cost effective way to remove a one-piece clutch brake. Remove the clutch from the flywheel.

Dixie123 Jul 17 2012 3 You must log in or sign up to reply here. You have to cut it out with a torch or air chisel. If the tab is near the REPLACE position the clutch should be replaced.

If both sides have a set screw bar the engine over again until you see the other side of the clutch brake with the set screw. Hold down clutch pedal so that tool and clutch brake are clamped together tightly. Remove the set screw.

Support the Clutch during the removal of the 8 mounting bolts. Bar the engine over until the slotted side with the set screw is accessible. What i do is use two 18th square pieces stock to hold brake in place.

Put one piece in front and one behind. The Kiene Diesel K-1360 one-piece clutch brake remover is a tool designed for removing a one-piece clutch brake. The tool eliminates the torch.

Drill through clutch brake up to collar. Ive also heard of using an air chisel. This will keep it from slipping.

The tool replaces the need to use a torch method and does not require the. Removing a one piece clutch brake is a difficult messy and hazardous job. Removing a clutch brake is a difficult messy hazardous job.

The safe and cost effective way to remove a one-piece clutch brake. Torch cutting is the usual solution but its slow and dangerous. Purchase with promo code TOOLPORN for a FREE gift with purchase.

Hi Im Wayne I will help you with this Good Morning The only way to remove a clutch brake is pull trans out or cut with a torch Reason being it is a complete circle so there is no way for it to slip off the new clutch brake is 2 piece and hinged. No need to pull transmission. Position the K-1360 and clamp in place with clutch pedal.

I picked up a Halldex two piece and installation of it looks easy. Drill through clutch brake. The tool replaces the need to use a torch method and does not require the transmission to be pulled from the vehicle in order to remove a clutch brake.

Kiene Diesel introduces a safe and cost effective way to remove a one piece clutch brake the company announced. Locate four 4 38 x 16 x 1 14 UNC hex head machine screws. If the clutch brake does in fact need to be replaced it isnt usually that bad.

Removing a one piece clutch brake is a difficult messy and hazardous job. Can buy 2-piece replacements but they wont be the torque limiting type no biggie. David Martin with Davids Heavy Duty Tool Sales shares the Clutch Brake Cutter by Kiene.

Additionally how do you remove a one piece clutch brake. It is not a big deal to just replace the clutch brake. K-1360 Clutch Brake Cutter Quickly removes one-piece clutch brakes for mechanical clutches.

Clutch Brake Cutter Hd 1080p Youtube